Electrical Monitoring Tool

Voltage Imbalance and Motor Derating Calculator

Calculate three-phase voltage imbalance per NEMA MG-1 and determine the required motor derating factor to prevent premature failure.

Why This Matters

A 3.5% voltage imbalance causes approximately 25 times more heat in the motor winding than the same percentage current imbalance. NEMA MG-1 requires motors to be derated when imbalance exceeds 1%. This calculator shows exactly how much.

The Science Behind Voltage Imbalance

Voltage imbalance in a three-phase system occurs when the phase voltages differ from each other. Even small differences, even a fraction of a percent, cause disproportionate effects inside the motor because of how the negative-sequence current component behaves relative to the positive-sequence component.

When voltage imbalance is present, a negative-sequence current flows through the stator windings in opposition to the motor's rotation. This counter-rotating flux produces a braking torque and generates significant heat. The winding temperature rise caused by this effect is roughly proportional to the square of the negative-sequence current, which is itself proportional to the voltage imbalance. This is the mechanism behind NEMA's finding that a 3.5% voltage imbalance generates approximately 25 times more heat than the equivalent percentage of current imbalance.

Sustained elevated winding temperatures accelerate insulation degradation according to the Arrhenius rate law: every 10°C rise in winding temperature above rated conditions roughly halves the insulation service life. A motor running continuously at even 2% voltage imbalance can lose years of expected lifespan, making derating not just a precaution but an engineering necessity.

The NEMA MG-1 derating curve (Figure 14-1) quantifies the capacity reduction required to keep winding temperatures within design limits when operating under imbalanced supply conditions. Derating means reducing the mechanical load on the motor shaft, not reducing voltage. The motor may still run at full electrical input, but its output capacity must be curtailed to prevent the excess heat from damaging the winding insulation.


NEMA MG-1 Formula

The formula below is taken directly from NEMA MG-1, Section 14.35. It defines voltage imbalance as the ratio of the maximum voltage deviation from average to the average voltage, expressed as a percentage.

Vavg = (V1 + V2 + V3) / 3
MaxDeviation = max( |V1 - Vavg|, |V2 - Vavg|, |V3 - Vavg| )
VoltageImbalance% = (MaxDeviation / Vavg) × 100

Note: IEC standards use a different formula based on symmetrical components (negative-sequence voltage / positive-sequence voltage). For typical distribution system imbalances, the NEMA and IEC methods yield similar results but are not identical. This calculator uses the NEMA MG-1 definition.


Calculator

Measured at motor terminals
Measured at motor terminals
Measured at motor terminals
Optional: Motor Rating (for derated capacity output)
Leave blank to skip
 
Please enter valid positive values for all three phase voltages.
Results
Average Voltage --V
Maximum Phase Deviation --V
Voltage Imbalance --%
NEMA MG-1 Derating Factor --


Derating Factor Reference Table

These values are derived from NEMA MG-1-2016 Figure 14-1. Linear interpolation is applied between breakpoints for intermediate imbalance values.

Voltage Imbalance Derating Factor Status
0.0%1.000No derating required
1.0%1.000Monitor: NEMA limit
2.0%0.9505% capacity reduction
3.0%0.88012% capacity reduction
4.0%0.82018% capacity reduction
5.0%0.76024% capacity reduction
>5.0%N/AConsult manufacturer
Source NEMA MG-1-2016, Motors and Generators, Section 14.35 and Figure 14-1 (Voltage Imbalance Derating Factor). International equivalent: IEC 60034-26:2006.
Scope and Limitations Applies to three-phase induction motors operating under NEMA MG-1. Does not account for harmonic distortion, single-phasing conditions, or motors operating below 40% rated load. Measure voltages at the motor terminals, not at the panel, for accurate results.
Tools on this site are provided for educational purposes only. Calculations are based on published engineering formulas and industry standards cited on each tool. Results do not constitute professional engineering advice. Do not make maintenance, safety, or operational decisions based solely on these outputs. Always verify results against your equipment manufacturer's documentation and consult a qualified engineer or reliability professional before acting. This site accepts no liability for decisions made using these tools.